Papex

Open problem · Chemistry · since 1912 · Open

Fuels from artificial photosynthesis

Can artificial photosynthesis turn sunlight, water and carbon dioxide into common fuels in a practical way?

Summary

Artificial photosynthesis aims to store sunlight directly as fuel, for example by splitting water into hydrogen or reducing carbon dioxide. Catalysts for the individual steps are widely studied, but no practical system has been demonstrated.

Why it is open

Artificial photosynthesis uses man-made systems that emulate natural photosynthesis to make fuels from carbon dioxide and water with sunlight as the only energy source, a concept that the 2022 solar fuels roadmap dates to the 1970s [11]. Three kinds of system are studied: solar cells wired to an electrolyser (photovoltaic electrolysis), integrated photoelectrochemical devices in which a light absorber carrying catalysts sits in the electrolyte, and particulate photocatalysts, powders or sheets that split water directly [11]. Their performance is usually given as solar-to-hydrogen (STH) or solar-to-fuel efficiency, the share of the energy in sunlight that ends up stored in the fuel.

Making fuel from sunlight is not in question; each of these systems has done it [4, 6, 9]. What is unresolved is doing it practically. In the roadmap's introduction, Gideon Segev, Roel van de Krol and Frances Houle write that "formulating a consistent set of agreed-upon targets is still a work in progress", but report broad agreement that a solar fuel module should last more than ten years in the field, be made by scalable, very cheap processes (below 300 US dollars per square metre) and convert more than 10% of solar energy into a specific product [11]. They add that efficiencies mostly fall short of the targets from techno-economic studies, especially for multi-carbon products, and that "lifetimes are measured in hours, not months or years" [11].

The problem is therefore several problems: high efficiency, long life, low cost and large area in the same system, and, for carbon-based fuels, selective reduction of carbon dioxide; for photoelectrochemical carbon dioxide reduction "many fundamental questions on reaction mechanisms, selectivity, and stability remain" [11]. No body sets a bar for a resolution, and projected efficiency and cost targets still show "significant spread" [11].

What is known

Reported efficiencies for hydrogen (1998–2023). Each device result below comes from a single group, under that group's conditions. In 1998 Oscar Khaselev and John Turner reported a monolithic device, a solar cell and photoelectrode in one piece, that split water at 12.4% efficiency, using the short-circuit current and the lower heating value of hydrogen [1]. In 2016 Jieyang Jia, Thomas Jaramillo and colleagues reported a 48-hour average STH efficiency of 30% for a triple-junction solar cell driving two polymer electrolyte membrane electrolysers, with the solar concentration tuned to the electrolysers [4]. In 2018 Wen-Hui Cheng and colleagues reported 19.3% (acidic electrolyte) and 18.5% (neutral) for a monolithic photoelectrochemical device under simulated sunlight [6]; in their preprint the photocurrent fell to small values within 3 hours in acid and kept 83% of its initial value after 20 hours at neutral pH [6]. For photocatalysts, Tsuyoshi Takata, Kazunari Domen and colleagues reported an external quantum efficiency (the fraction of incident photons used) of up to 96% for aluminium-doped strontium titanate, at ultraviolet wavelengths of 350–360 nm [8]. The roadmap gives 1% STH for particle-based photocatalytic water splitting at ambient pressure, one order of magnitude lower than electrolysers and photoelectrochemical cells powered by solar cells [11]. In 2023 Peng Zhou, Zetian Mi and colleagues reported 9.2% STH from pure water with an indium gallium nitride photocatalyst under concentrated light at about 70 °C, about 7% from tap and sea water, and 6.2% in a larger system under natural sunlight with a capacity of 257 watts [12].

Scale (2021–2023). Hiroshi Nishiyama, Domen and colleagues operated a 100 m² array of photocatalyst panel reactors for several months, recovering hydrogen from the mixed hydrogen–oxygen product with a commercial membrane; the system stayed undamaged when recovered hydrogen was deliberately ignited [9]. Its maximum STH was 0.76%, and they write that the production "is inefficient and energy negative overall" [9]. Isaac Holmes-Gentle, Sophia Haussener and colleagues ran a kilowatt-scale photoelectrochemical plant at about 800 times solar concentration for more than 13 days in 2020 and 2021; on a Gibbs free energy basis, its average device-level STH efficiency was 20.3%, but its system-level fuel efficiency, counting the electricity used by auxiliary equipment, was 5.5% [13]. They write that it must be run over several years to support their hypothesis of long-term stability [13].

Stability. Cheng, Todd Deutsch and Chengxiang Xiang write in the roadmap that photoelectrochemical devices are "currently limited by stability and overall generation rate", that "no reasonably efficient material is intrinsically stable" in that configuration, and that pinhole-free protective layers over large areas have "remained elusive" [11].

Fuels from carbon dioxide (2019–2024). Tran Ngoc Huan, Victor Mougel and colleagues coupled a perovskite solar module to copper-based electrodes and reached 2.3% solar-to-hydrocarbon efficiency, making ethylene and ethane [7]. Floating artificial leaves from Virgil Andrei, Erwin Reisner and colleagues reached unassisted solar-to-fuel efficiencies of 0.58% for hydrogen and 0.053% for carbon monoxide, with about 24 hours of stability at 100 cm² [10]. A 2024 review by Takashi Hisatomi, Domen and colleagues says that for photocatalyst systems with two light-absorbing steps (Z-schemes), the STH and the solar-to-fuel efficiency of carbon dioxide reduction are "still approximately 1% at most, which is below the practical target" [14]. Products are usually mixtures, because perfect selectivity and complete single-pass use of carbon dioxide have not been achieved [11].

Main approaches

Photovoltaic electrolysis. Solar cells wired to separate electrolysers [11]. Strongest evidence: 30% STH over 48 hours in the laboratory [4]; among the best demonstrations in the roadmap's survey is a concentrated system at 31% STH under 42 suns [11]; and pilot plants have been built worldwide [14]. Main difficulty: cost. In a 2016 assessment for a plant making 10,000 kg of hydrogen a day, Matthew Shaner and colleagues found plant-gate costs of 12.1 US dollars per kg for an off-grid base case at 9.8% efficiency, against 5.5 dollars for grid electrolysis at 0.07 dollars per kWh [3]; Hisatomi and colleagues judge large-scale solar hydrogen from such plants "likely still more expensive" than hydrogen from fossil resources [14].

Integrated photoelectrochemical devices. Absorber and catalyst in one unit [11]. Strongest evidence: 19.3% in the laboratory [6] and over 20% device-level efficiency at kilowatt scale [13]. Main difficulty: stability [11], and a system efficiency well below the device efficiency [13]. Shaner's unconcentrated base case gave 11.4 dollars per kg [3]. A 2013 study by Blaise Pinaud and colleagues, using the US Department of Energy H2A model for four hypothetical 10-tonne-per-day plants, two with suspended photocatalyst particles and two with panels, found 1.60–10.40 dollars per kg, with the particle beds cheaper than the panel-based systems [2].

Particulate photocatalysts. Powders or sheets that are potentially simpler, cheaper and easier to scale up [14]. Strongest evidence: near-unity quantum efficiency in ultraviolet light [8] and safe operation at 100 m² [9]. Main difficulty: efficiency. The roadmap says photocatalysts are expected to reach 5–10% STH or more to be economically feasible [11]; the 100 m² system was energy negative [9]; and producing hydrogen and oxygen together raises safety concerns [2]. Hisatomi, Frank Osterloh and Domen write in the roadmap that even at 10% STH and a ten-year life, such a system should cost no more than 100 dollars per m² for hydrogen at 3.5 dollars per kg [11]. A 2024 review by Hisatomi and colleagues gives 0.5–1.7 dollars per kg for hydrogen made from natural gas [14].

Direct carbon dioxide reduction. Making carbon-based fuels directly [7, 10]. Strongest evidence: the hydrocarbon and leaf demonstrations [7, 10]. Main difficulty: low efficiency and mixed products [11, 14]. In Matthew Jouny, Wesley Luc and Feng Jiao's 2018 analysis of carbon dioxide electrolysers producing 100 tonnes a day, only carbon monoxide and formic acid were economically viable under then-current conditions [5]. Shaner and colleagues list carbon dioxide mass transport and feedstock cost among unmet challenges [3]. Holmes-Gentle and colleagues suggest combining solar hydrogen with direct air capture to make carbon-based fuels [13]; see economical direct air capture.

Open sub-questions

  1. Visible light. Can a particulate photocatalyst combine high quantum yield with response to long wavelengths, which the roadmap says no particle-based system has achieved together [11]?
  2. Durability at 70 °C. Does the indium gallium nitride photocatalyst keep its 6.2% efficiency under natural sunlight over months of daily cycling [12]?
  3. Energy balance. At what STH efficiency and gas-separation cost would a 100 m² panel array produce more energy than it uses [9]?
  4. Protective layers. Which coating protects an efficient photoelectrode over large areas without pinholes [11]?
  5. Leaf durability. Can floating perovskite–BiVO₄ leaves run for weeks rather than about 24 hours while keeping their carbon monoxide selectivity [10]?
  6. Selective carbon dioxide reduction. Which catalyst gives a single carbon product with high single-pass conversion in a solar-driven device [7, 11]?

Work on this in Papex

If you have a testable answer to one of the sub-questions above, you can draft it as a private hypothesis in Papex, or prepare the draft from Claude or ChatGPT with the Papex connector. You review the exact version, sign it and decide whether to publish it; a public record that names this problem is listed on this page. A Papex record shows who signed which version and when. It is not peer review and does not mean the hypothesis is correct.

Key references

  1. Khaselev, O. & Turner, J. A. (1998). A monolithic photovoltaic-photoelectrochemical device for hydrogen production via water splitting. Science 280(5362), 425–427. 10.1126/science.280.5362.425 · Checked 15 Oct 2026
  2. Pinaud, B. A., Benck, J. D., Seitz, L. C., Forman, A. J., Chen, Z., Deutsch, T. G. et al. (2013). Technical and economic feasibility of centralized facilities for solar hydrogen production via photocatalysis and photoelectrochemistry. Energy & Environmental Science 6(7), 1983. 10.1039/c3ee40831k · Checked 15 Oct 2026
  3. Shaner, M. R., Atwater, H. A., Lewis, N. S. & McFarland, E. W. (2016). A comparative technoeconomic analysis of renewable hydrogen production using solar energy. Energy & Environmental Science 9(7), 2354–2371. 10.1039/C5EE02573G · Checked 15 Oct 2026
  4. Jia, J., Seitz, L. C., Benck, J. D., Huo, Y., Chen, Y., Ng, J. W. D., Bilir, T., Harris, J. S. & Jaramillo, T. F. (2016). Solar water splitting by photovoltaic-electrolysis with a solar-to-hydrogen efficiency over 30%. Nature Communications 7, 13237. 10.1038/ncomms13237 · Checked 15 Oct 2026
  5. Jouny, M., Luc, W. & Jiao, F. (2018). General techno-economic analysis of CO2 electrolysis systems. Industrial & Engineering Chemistry Research 57(6), 2165–2177. 10.1021/acs.iecr.7b03514 · Checked 15 Oct 2026
  6. Cheng, W.-H., Richter, M. H., May, M. M., Ohlmann, J., Lackner, D., Dimroth, F. et al. (2018). Monolithic photoelectrochemical device for direct water splitting with 19% efficiency. ACS Energy Letters 3(8), 1795–1800. 10.1021/acsenergylett.8b00920 · Checked 15 Oct 2026
  7. Huan, T. N., Dalla Corte, D. A., Lamaison, S., Karapinar, D., Lutz, L., Menguy, N. et al. (2019). Low-cost high-efficiency system for solar-driven conversion of CO2 to hydrocarbons. Proceedings of the National Academy of Sciences 116(20), 9735–9740. 10.1073/pnas.1815412116 · Checked 15 Oct 2026
  8. Takata, T., Jiang, J., Sakata, Y., Nakabayashi, M., Shibata, N., Nandal, V., Seki, K., Hisatomi, T. & Domen, K. (2020). Photocatalytic water splitting with a quantum efficiency of almost unity. Nature 581(7809), 411–414. 10.1038/s41586-020-2278-9 · Checked 15 Oct 2026
  9. Nishiyama, H., Yamada, T., Nakabayashi, M., Maehara, Y., Yamaguchi, M., Kuromiya, Y. et al. (2021). Photocatalytic solar hydrogen production from water on a 100-m² scale. Nature 598(7880), 304–307. 10.1038/s41586-021-03907-3 · Checked 15 Oct 2026
  10. Andrei, V., Ucoski, G. M., Pornrungroj, C., Uswachoke, C., Wang, Q., Achilleos, D. S. et al. (2022). Floating perovskite-BiVO4 devices for scalable solar fuel production. Nature 608(7923), 518–522. 10.1038/s41586-022-04978-6 · Checked 15 Oct 2026
  11. Segev, G., Kibsgaard, J., Hahn, C., Xu, Z. J., Cheng, W.-H., Deutsch, T. G. et al. (2022). The 2022 solar fuels roadmap. Journal of Physics D: Applied Physics 55(32), 323003. 10.1088/1361-6463/ac6f97 · Checked 15 Oct 2026
  12. Zhou, P., Navid, I. A., Ma, Y., Xiao, Y., Wang, P., Ye, Z., Zhou, B., Sun, K. & Mi, Z. (2023). Solar-to-hydrogen efficiency of more than 9% in photocatalytic water splitting. Nature 613(7942), 66–70. 10.1038/s41586-022-05399-1 · Checked 15 Oct 2026
  13. Holmes-Gentle, I., Tembhurne, S., Suter, C. & Haussener, S. (2023). Kilowatt-scale solar hydrogen production system using a concentrated integrated photoelectrochemical device. Nature Energy 8(6), 586–596. 10.1038/s41560-023-01247-2 · Checked 15 Oct 2026
  14. Hisatomi, T., Wang, Q., Zhang, F., Ardo, S., Reisner, E., Nishiyama, H., Kudo, A., Yamada, T. & Domen, K. (2024). Photocatalytic water splitting for large-scale solar-to-chemical energy conversion and storage. Frontiers in Science 2, 1411644. 10.3389/fsci.2024.1411644 · Checked 15 Oct 2026

Page reviewed 15 Oct 2026

Source

Open, as listed by Wikipedia · Unsolved problems in chemistry. Checked 08 Oct 2026.

The status is the source’s. Papex does not decide whether a problem is solved.

Records on this problem

No public record addresses this problem yet.

More in Chemistry